 首頁 \ 關于遠東
|
| 首頁 關于遠東 產品目錄 銷售網絡 生產設備 公司資質 技術支持 聯系我們
 高粘度打膠泵用NYP110高粘度泵配XWD7.5KW-7-9減速機
高粘度齒輪泵并不能產生壓力，它只是輸出流量。壓力低或無壓力，說明高粘度齒 輪泵沒有吸入液體或泄漏嚴重。High viscosity gear pump
does not generate pressure, it is only the output flow.Pressure is low or no
pressure, high viscosity gear wheel pump don't inhale the liquid or leakage
is serious.
電動機輸出功率偏小、齒 輪泵排量選得過大或壓力調得過高時，也會造成壓力不足 當然，壓力表損壞或壓力表節流孔堵塞時也顯示不出壓力，此時可換裝一個新的壓力表檢查。Small
motor output power, gear wheel pump capacity to choose too large or pressure
too high, can cause stress Pressure gauge damage or pressure gauge orifice
jams, of course, also could not show pressure, can change a new pressure gauge
to check at this time.
如果確認泵無流量輸出，可能是由于泵安裝有誤、泵的轉向不對，或吸人側(進液口及吸液管道)堵塞、出口止回閥裝反或卡死了，也有可能是驅動軸斷裂了。If
confirmed that no flow pump output, could be turned to the pumps due to pump
installation is wrong, wrong, or suction side (liquid into the mouth and suck
liquid pipeline jam, export check valve installed backwards, or card is dead,
it is possible that the drive shaft fracture.
高粘度泵在轉速過低時會引起出液量不足，這種現象往往是由于泵的驅動裝置打滑或功率不足所致。此時應檢查齒 輪泵的實際轉速、泵與電動機的聯接及功率匹配情況等。High
viscosity pump in low speed can cause insufficient quantity of produced liquid,
this phenomenon is often due to the slippage of the pump drive or insufficient
power.Check the gear wheel pump at this time of the actual speed, pump and
motor connection and power matching, etc.
高粘度泵在開始運轉前，往齒輪泵的殼體內灌滿待輸送的液體，便于安全啟動。若環境溫度低于冰點，應預先向泵內通入熱蒸汽，進行預熱處理，然后才可啟動齒輪泵。高粘度泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置后再使用，最好在空載或小負荷情況下先跑合一小時左右。如果在跑合階段預先覺察出異常溫升、泄漏、振動和噪聲時，應停機檢查。高粘度齒輪泵的支座或法蘭與其驅動電機應采用共同的安裝基礎，基礎、法蘭或支座均需具有足夠的剛度，以減小齒輪泵運轉時產生的振動和噪聲。電動機與齒輪泵須用彈性聯軸器連接，同軸度小于0.1毫米，傾斜角不得大于1度。安裝聯軸器時不得用錘敲打，以免傷害齒輪泵的齒輪等零件。若用帶輪、鏈輪等驅動時應設托架支承，以防主動齒輪軸承受徑向力。緊固齒輪泵、電動機的地腳螺釘時，螺釘受力應均勻，連接可靠。用手轉動聯軸器時，應感覺到齒輪泵能夠輕松地轉動，沒有卡緊等異�，F(xiàn)象出現，然后才可以配管。High
viscosity pump before starting work, to gear pump casing filled with liquid,
facilitate safe launch.If the environment temperature is below freezing,
should advance to pump into the hot steam, preheating treatment, and then
to start the pump.The direction of rotation of the pump with high viscosity,
oil outlet in accord.Gear pump is the first run, or long-term idle before
using, had better under the condition of no load or small load to run one
hour or so.If in the running-in stage in advance detect abnormal temperature
rise, leakage, vibration and noise, should stop check.High viscosity gear
pump bearing or flange should adopt a common drive motor installationFoundation,
foundation, flange or support all needs to have enough rigidity, to reduce
the vibration of gear pump is running and noise.Motor and gear pump with
elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not
be greater than 1 degree.When installing coupling hammer shall not be used,
in order to avoid damage of the gear pump gearAnd other parts.If use the
belt wheel, wheel, etc, shall set bracket support, in case of driving gear
bearing by the radial force.Ground screw fastening gear pump, motor, screw
force should be uniform, reliable connection.Turn the coupling with the hand,
should feel can easily turn the gear pump, no abnormal phenomenon such as
clamping, then can be piping.
高粘度齒輪泵的吸油管道內徑應足夠大，并避免狹窄通道或急劇拐彎、減少彎頭，去除不必要的閥門、附件，盡可能地降低泵的安裝高度，縮短吸油管道的長度，以減少壓力損失。管接頭等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。止回閥與安全閥在齒輪泵的輸出管路上最好安裝一個止回閥。這樣在檢修泵及輸出管道時，系統中的液體不會發生倒流。齒輪泵帶負荷停車時，亦可防止泵倒轉而在其輸出管道內產生局部真空。應當注意，出口止回閥不能裝反或出現卡死現象。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。安全閥可以與泵體或泵蓋鑄成一體，也可以單獨裝配。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High
viscosity gear pump oil suction pipe diameter should be large enough, and to
avoid the narrow channel, or a sharp turn, reducing elbow, remove unnecessary
valves, fittings, as much as possible to reduce the installation height of
pump, shorten the length of the oil suction pipe, in order to reduce the pressure
loss.Components, such as pipe joint sealed well, in order to prevent the air
intrusion, thus control air-pocket and the occurrence of cavitation.Check valve
and relief valve on the output of the gear pump tube had better install a check
valve.In the overhaul pump and output pipe, the system of fluid backflow will
not occur.Gear pump to stop loading machine, can be in the output pipe to prevent
pump reverse, and create a partial vacuum.It should be noted that the outlet
check valve cannot be installed backwards or stuck.High viscosity of the pump
outlet pipe also shall set up relief valve or other protective device on the
road, so that once the clogging pump export channels, can open the relief valve
pressure relief.The relief valve can be cast and pump body and pump cover,
also can separate assembly.For high viscosity gear pump need positive &negative,
import and export all needs to set up the line safety valve.
高粘度泵是輸送高粘度液體的齒輪泵，應做到在較低的功耗、較少的泄漏、較大的壓力下輸出最多的流量。在確定所要輸送的介質時，應該嚴格遵循產品說明書上的規定，盡量使用廠家推薦的流體介質，并注意考慮系統的工作溫度范圍。當希望在某一較寬的溫度范圍內使用時，輸送介質的粘度指數應該高些。輸送介質不僅是能量傳遞的中介，而且也是潤滑、密封及傳熱介質。液體粘度過高會增加內摩擦阻力，降低輸出功率，浪費能量，并產生過高的系統溫度.高粘度齒輪泵的出口管路上應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High
viscosity pump is conveying liquid with high viscosity gear pump, should be
in lower power consumption, less leakage, under the pressure of large output
the most traffic.When determining to conveying medium, we should strictly follow
the provisions of the product manuals on use manufacturers recommend fluid
as far as possible, and pay attention to consider the system operating temperature
range.When you want to use in a wide temperature range, medium viscosity index
should be higher.Medium is not only the energy transfer intermediary, but also
lubrication, sealing and heat transfer medium.Liquid viscosity is too high
will increase internal friction resistance, lower output power, waste of energy,
and generate high temperature system. High viscosity gear pump outlet pipe
shall set up relief valve or other protective device on the road, so once the
clogging pump export channels, can open the relief valve pressure relief.For
high viscosity gear pump need positive &negative, import and export all
needs to set up the line safety valve.
1、工作壓力的選定1, select the work pressure
高粘度泵額定的壓力是指泵連續工作時的最高許用壓力，而其工作壓力則決定于外部負載，安裝和調試的壽命與其工作壓力直接相關。對于不頻繁工作的齒輪泵，其工作壓力可取為泵的額定壓力，考慮到產品質量不同，最好將額定壓力降低20%～30%使用。對于經常工作于較高壓力下的齒輪泵，其工作壓力應比泵的額定壓力低1～2個壓力級。石油化工設備常常是24小時連續運轉，這時泵的工作壓力應該取得比額定壓力低得多，且工作轉速也應該低于額定轉速。如果高粘度齒輪泵的工作壓力調整過高，則會使齒輪泵在超負荷下運行。High
viscosity pump rated pressure refers to the maximum allowable pump continuous
work pressure, and its working pressure is determined by the external load,
installation and commissioning of life is directly related with work pressure.For
not frequent work gear pump, the working pressure is desirable for the rated
pressure of the pump, taking the quality into consideration, it is best to
used pressure rated lower 20% ~ 30%.For often work under high pressure gear
pump, the working pressure shall be lower than the rated pressure of the pump
1 ~ 2 pressure level.Petrochemical equipment are often 24 hours of continuous
operation, and at this time of the pump working pressure should be obtained
was much lower than the rated pressure, and the work speed should be lower
than the rated speed.If the high viscosity gear pump high pressure adjustment,
will make the pump running under overload.
2.安裝與試運轉2. Installation and commissioning
高粘度泵的支座或法蘭與其驅動電機應采用共同的安裝基礎，基礎、法蘭或支座均需具有足夠的剛度，以減小齒輪泵運轉時產生的振動和噪聲。電動機與齒輪泵須用彈性聯軸器連接，同軸度小于0.1毫米，傾斜角不得大于1度。安裝聯軸器時不得用錘敲打，以免傷害齒輪泵的齒輪等零件。若用帶輪、鏈輪等驅動時應設托架支承，以防主動齒輪軸承受徑向力。緊固齒輪泵、電動機的地腳螺釘時，螺釘受力應均勻，連接可靠。用手轉動聯軸器時，應感覺到齒輪泵能夠輕松地轉動，沒有卡緊等異�，F(xiàn)象出現，然后才可以配管。高粘度齒輪泵的吸油管道內徑應足夠大，并避免狹窄通道或急劇拐彎、彎頭，去除不必要的閥門、附件，盡可能地降低泵的安裝高度，縮短吸油管道的長度，以減少壓力損失。管接頭等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。在開始運轉前，往齒輪泵的殼體內灌滿待輸送的液體，便于安全動。若環境溫度低于冰點，應預先向泵內通入熱蒸汽，進行預熱處理，然后才可啟動齒輪泵。齒輪泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置后再使用，最好在空載或小負荷情況下先跑合一小時左右。如果在跑合階段預先覺出異常溫升、泄漏、振動和噪聲時，應機檢查。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High
viscosity pump bearing or flange and its drive motor should use common installation
basis, foundation, flange or support all needs to have enough rigidity, to
reduce the vibration of gear pump is running and noise.Motor and gear pump
with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall
not be greater than 1 degree.When installing coupling hammer shall not be used,
in order to avoid damage gear and other parts of the gear pump.If use the belt
wheel, wheel, etc, shall set bracket support, in case of driving gear bearing
by the radial force.Ground screw fastening gear pump, motor, screw force should
be uniform, reliable connection.Turn the coupling with the hand, should feel
can easily turn the gear pump, no abnormal phenomenon such as clamping, then
can be piping.High viscosity gear pump oil suction pipe diameter should be
large enough, and to avoid the narrow channel, or a sharp bend, bend, remove
unnecessary valves, fittings, as much as possible to reduce the installation
height of pump, shorten the length of the oil suction pipe, in order to reduce
the pressure loss.Components, such as pipe joint sealed well, in order to prevent
the air intrusion, thus control air-pocket and the occurrence of cavitation.Before
starting operation, to gear pump casing filled with liquid, easy to safety.If
the environment temperature is below freezing, should advance to pump into
the hot steam, preheating treatment, and then to start the pump.Direction of
rotation of the gear pump, oil outlet in accord.Gear pump is the first run,
or long-term idle before using, had better under the condition of no load or
small load to run one hour or so.If in the running-in stage in advance the
abnormal temperature rise, leakage, vibration and noise, should machine inspection.High
viscosity of the pump outlet pipe also shall set up relief valve or other protective
device on the road, so that once the clogging pump export channels, can open
the relief valve pressure relief.For high viscosity gear pump need positive &negative,
import and export all needs to set up the line safety valve.
如何選型How to choice
選擇高粘度泵時應該注意泵所輸送的具體粘度、工作溫度、介質比重、介質成分等等，只有更好的了解高粘度泵所輸送的介質情況才能更好的選擇所需要的高粘度泵產品。
Should be paid attention to when selecting high viscosity pump pump delivery
by the specific viscosity, working temperature, the proportion of medium, medium
composition etc., only a better understanding of the high viscosity pump transmission
medium condition can better choose the required high viscosity pump product.
第一、必須了解高粘度泵所輸送的介質粘度。因?yàn)榻橘|(zhì)粘度的高低直接影響到選擇高粘度泵的轉速。must understand the high viscosity
pump transmission medium viscosity. Because the medium viscosity directly affects
the choice of high viscosity pump speed.
第二、了解高粘度泵所輸送介質的性質，例如有沒有腐蝕性。understand the nature of the high viscosity pump
conveying medium, such as corrosive.
第三、高粘度泵所輸送的介質濃度多少、比重多少。 high viscosity pump how far the conveying medium
concentration, specific gravity.
Fourth,
第四、高粘度泵所輸送的介質。high viscosity pump transmission medium.
第五、高粘度泵輸送的介質常溫下是否結晶或凝固。the high viscosity pump whether the medium temperature
of crystallization or coagulation.
第六、高粘度泵所輸送的介質是否有懸浮物。the transmission medium for high viscosity pump suspension.
第七、高粘度泵所輸送介質受溫度變化情況。high viscosity pump conveying medium affected by temperature
changes.
第八、高粘度泵所輸送介質的潤滑性、清潔度、腐蝕性等。high viscosity pump medium by lubricity, cleanliness,
corrosion resistance, etc.
第九、高粘度泵要求進口壓力及出口壓力和安裝高度。 high viscosity pump inlet pressure and outlet pressure
and the installation height.
第十、高粘度泵使用場合的防爆要求。high viscosity pump occasions of explosion-proof requirements.
高粘度泵的安裝調試步驟High viscosity pump installation and debugging steps
高粘度泵是輸送高粘度液體的齒輪泵，應做到在較低的功耗、較少的泄漏、較大的壓力下輸出最多的流量。在確定所要輸送的介質時，應該嚴格遵循產品說明書上的規定，盡量使用廠家推薦的流體介質，并注意考慮系統的工作溫度范圍。當希望在某一較寬的溫度范圍內使用時，輸送介質的粘度指數應該高些。輸送介質不僅是能量傳遞的中介，而且也是潤滑、密封及傳熱介質。液體粘度過高會增加內摩擦阻力，降低輸出功率，浪費能量，并產生過高的系統溫度.高粘度齒輪泵的出口管路上應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High
viscosity pump is conveying liquid with high viscosity gear pump, should
be in lower power consumption, less leakage, under the pressure of large
output the most traffic. When determining to conveying medium, we should
strictly follow the provisions of the product manuals on use manufacturers
recommend fluid as far as possible, and pay attention to consider the system
operating temperature range. When you want to use in a wide temperature range,
medium viscosity index should be higher. Medium is not only the energy transfer
intermediary, but also lubrication, sealing and heat transfer medium. Liquid
viscosity is too high will increase internal friction resistance, lower output
power, waste of energy, and generate high temperature system. High viscosity
gear pump outlet pipe shall set up relief valve or other protective device
on the road, so once the clogging pump export channels, can open the relief
valve pressure relief. For high viscosity gear pump need positive &negative,
import and export all needs to set up the line safety valve.
1、工作壓力的選定1, select the work pressure
高粘度泵額定的壓力是指泵連續工作時的最高許用壓力，而其工作壓力則決定于外部負載，高粘度泵(聚氨酯泵,紙漿泵,粘合劑泵)的安裝和調試 的壽命與其工作壓力直接相關。對于不頻繁工作的齒輪泵，其工作壓力可取為泵的額定壓力，考慮到產品質量不同，最好將額定壓力降低20%～30%使用。對于經常工作于較高壓力下的齒輪泵，其工作壓力應比泵的額定壓力低1～2個壓力級。石油化工設備常常是24小時連續運轉，這時泵的工作壓力應該取得比額定壓力低得多，且工作轉速也應該低于額定轉速。如果高粘度齒輪泵的工作壓力調整過高，則會使齒輪泵在超負荷下運行。High
viscosity pump rated pressure refers to the maximum allowable pump continuous
work pressure, and its working pressure is determined by the external load,
high viscosity pump (pu pump, paper pulp pump, glue pump) installation and
commissioning of life is directly related with work pressure. For not frequent
work gear pump, the working pressure is desirable for the rated pressure
of the pump, taking the quality into consideration, it is best to used pressure
rated lower 20% ~ 30%. For often work under high pressure gear pump, the
working pressure shall be lower than the rated pressure of the pump 1 ~ 2
pressure level. Petrochemical equipment are often 24 hours of continuous
operation, and at this time of the pump working pressure should be obtained
was much lower than the rated pressure, and the work speed should be lower
than the rated speed. If the high viscosity gear pump high pressure adjustment,
will make the pump running under overload.
2.安裝與試運轉2. Installation and commissioning
高粘度泵的支座或法蘭與其驅動電機應采用共同的安裝基礎，基礎、法蘭或支座均需具有足夠的剛度，以減小齒輪泵運轉時產生的振動和噪聲。電動機與齒輪泵須用彈性聯軸器連接，同軸度小于0.1毫米，傾斜角不得大于1度。安裝聯軸器時不得用錘敲打，以免傷害齒輪泵的齒輪等零件。若用帶輪、鏈輪等驅動時應設托架支承，以防主動齒輪軸承受徑向力。緊固齒輪泵、電動機的地腳螺釘時，螺釘受力應均勻，連接可靠。用手轉動聯軸器時，應感覺到齒輪泵能夠輕松地轉動，沒有卡緊等異�，F(xiàn)象出現，然后才可以配管。高粘度齒輪泵的吸油管道內徑應足夠大，并避免狹窄通道或急劇拐彎、減少彎頭，去除不必要的閥門、附件，盡可能地降低泵的安裝高度，縮短吸油管道的長度，以減少壓力損失。管接頭等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。在開始運轉前，往齒輪泵的殼體內灌滿待輸送的液體，便于安全啟動。若環境溫度低于冰點，應預先向泵內通入熱蒸汽，進行預熱處理，然后才可啟動齒輪泵。齒輪泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置后再使用，最好在空載或小負荷情況下先跑合一小時左右。如果在跑合階段預先覺察出異常溫升、泄漏、振動和噪聲時，應機檢查。High
viscosity pump bearing or flange and its drive motor should use common
installation basis, foundation, flange or support all needs to have enough
rigidity, to reduce the vibration of gear pump is running and noise. Motor
and gear pump with elastic shaft coupling, coaxial degree is less than
0.1 mm, Angle shall not be greater than 1 degree. When installing coupling
hammer shall not be used, in order to avoid damage gear and other parts
of the gear pump. If use the belt wheel, wheel, etc, shall set bracket
support, in case of driving gear bearing by the radial force. Ground screw
fastening gear pump, motor, screw force should be uniform, reliable connection.
Turn the coupling with the hand, should feel can easily turn the gear pump,
no abnormal phenomenon such as clamping, then can be piping. High viscosity
gear pump oil suction pipe diameter should be large enough, and to avoid
the narrow channel, or a sharp turn, reducing elbow, remove unnecessary
valves, fittings, as much as possible to reduce the installation height
of pump, shorten the length of the oil suction pipe, in order to reduce
the pressure loss. Components, such as pipe joint sealed well, in order
to prevent the air intrusion, thus control air-pocket and the occurrence
of cavitation. Before starting operation, to gear pump casing filled with
liquid, facilitate safe launch. If the environment temperature is below
freezing, should advance to pump into the hot steam, preheating treatment,
and then to start the pump. Direction of rotation of the gear pump, oil
outlet in accord. Gear pump is the first run, or long-term idle before
using, had better under the condition of no load or small load to run one
hour or so. If in the running-in stage in advance detect abnormal temperature
rise, leakage, vibration and noise, should machine inspection.
高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High
viscosity of the pump outlet pipe also shall set up relief valve or other
protective device on the road, so that once the clogging pump export channels,
can open the relief valve pressure relief. For high viscosity gear pump need
positive &negative, import and export all needs to set up the line safety
valve.
輸送介質的優勢:The advantage of the medium:
高粘度泵可以輸送高粘度、高濃度無固體顆�；蚣�(xì)小軟顆粒的潤滑性介質；效率高，性能穩定，使用壽命長。高粘度泵可以采用保溫夾套結構，輸送比較高的粘度物料時可以對高粘度泵進行保溫，從而降低介質粘度，達到更好的輸送效果，而單螺桿泵沒有保溫夾套結構；高粘度泵在使用一段時間后，如果泵內部間隙磨損后，不用拆泵可以自行根據高粘度泵所輸送的物料粘度來調整泵的間隙，調整后和新泵一樣可以達到良好的使用效果。高粘度泵可配安全閥，當泵或管路系統超壓時，安全閥門打開，形成內部回流，保證系統安全。而單螺桿泵在泵本身不能設置安全閥，只能在管路中設置，提高了設備投入成本和安裝成本。選擇高粘度泵時必須考慮高粘度泵所輸送的介質粘度，從而才能來確定高粘度泵的轉速范圍，根據高粘度泵的轉速范圍及所需工況條件下高粘度泵的正常流量范圍，才能確定高粘度泵具體型號。需要注意的是一般介質可以這樣來選擇。High
viscosity pump can transport high viscosity, high concentration without solid
particles or small soft particles lubricity medium; High efficiency, stable
performance and long service life. High viscosity pump can be used in a heat
preservation jacket structure, transmission is higher when the viscosity
of the material can be for thermal insulation in high viscosity pump, thereby
reducing medium viscosity, achieve better transmission effect, and the single
screw pump heat preservation jacket structure; High viscosity pump in use
after a period of time, if the pump internal clearance after wear, don't
have to dismantle the pump to according to the viscosity of material delivery
by high viscosity pump to adjust the clearance between the pump and adjusted,
and the use of the new pump can achieve good effect. High viscosity pump
can match the relief valve, when the pump and piping system overpressure,
safety valve is opened, the formation of internal reflux, ensure the safety
of the system. And single screw pump in the pump itself cannot set the relief
valve, can only be set up in line, increase the investment of equipment cost
and installation cost. Choosing high viscosity pump must consider the conveying
medium viscosity, high viscosity pump order to determine the scope of the
high viscosity of the pump rotation speed, according to the working condition
of high viscosity of the pump speed range and required high viscosity pump
under the condition of normal flow range, to determine the high viscosity
pump concrete models. It's important to note that it can be to choose a normal
medium.
其中，有些特殊化學介質在一定溫度下會改變其化學成分，所以需要在選擇高粘度泵要特別注意泵的轉速是否適合，因?yàn)楸玫霓D(zhuǎn)速越高，正常工作中產生的熱量就越大，一旦超過介質所限制的溫度，那么就多所輸送的介質造成了破壞。還有些食品類介質，比如果醬類，像我們?nèi)粘Ｖ兴秤玫墓u、花生醬、豆瓣醬等，這些介質要求在輸送過程中必須不能夠破壞其內部的成分進行破壞，這就要求我們所選的泵的轉速必須要低，才能保證高粘度泵在輸送過程中不破壞所輸送的介質。高粘度泵在運轉過程中常常會出現卡死、抱軸轉不動的現象，主要原因是高粘度泵往往都是輸送的高粘度的介質，有些是有一些雜質的混合物理。如果泵的入口沒有安裝合適的過濾器，那么一旦大一些的硬質顆粒進入泵腔就會把高粘度泵的內外轉子卡死，使泵轉不動，嚴重的會把高粘度泵的內外轉子毀掉。Among
them, some special chemical medium under a certain temperature to change its
chemical composition, so need to high viscosity pump in the choice whether
to pay special attention to the speed of the pump is suitable for, because
the higher the pump rotation speed, the greater the heat generated by the normal
work, once more than media limited by temperature, then it is more than conveying
medium caused damage. Also some food medium, such as the jam class, as in our
daily consumption of jam, peanut butter, broad bean paste and so on, these
medium requirements must be in the process of conveying can't destroy its internal
composition, this requires that we selected the speed of the pump must be low,
to ensure high viscosity pump does not destroy the transmission medium in the
process of delivery. High viscosity pump in the operation process often appear
stuck, holding shaft fixed phenomenon, the main reason is that high viscosity
pump are often transport high viscosity medium, some are some impurities mixed
in physics. If the entrance of the pump is not installed the appropriate filters,
so once the larger hard particle enters the pump chamber would bring high viscosity
pump rotor stuck inside and outside, make the pump turns motionless, serious
will destroy high viscosity pump inside and outside of the rotor.
所以建議大家在安裝高粘度泵的時候應該選擇合適的過濾器來安裝在泵的入口。高粘度泵抱軸的現象主要體現在不銹鋼高粘度泵的較多，因?yàn)椴讳P鋼材質含碳量低，所以熱膨脹系數大，一旦泵的溫度過高，就會造成泵的內部配件與配件之間的間隙縮小，到一定程度以后就會產生抱死現象。所以選擇不銹鋼材質的高粘度泵是一定要注明具體的使用溫度，及介質的潤滑性。介質粘度的高低與高粘度泵的轉速有著密不可分的關系。如果高粘度泵輸送的介質粘度過高，而所配的轉速也過高的話，就會造成泵的流量很低、泵的噪音很大。如果電機功率還是按常規來配的話，那么電機也會造成過載。主要是泵的轉速太高、介質粘度又太高這樣就會造成泵阻力很大，電機的瞬間啟動電流超過額定電流，造成電機過載；由于轉速過高，使高粘度泵在運轉時內部轉子幾乎只是形成了空轉，圍繞所輸送介質打滑，造成吸不上料，或者是流量很小。在這種狀況下，必須降低泵的轉速，加大電機的功率，加大進出口的管徑來減少介質的流動阻力。從而來完成介質的輸送工作。轉速降低以后，泵的流量會反而增加，而且泵的噪音會降低，但肯定打不到理論流量。所以如果與實際工況需要流量相差太多的話，那就只能更好型號更大一點的泵。So
suggest you at the time of installation of high viscosity pump should choose
the appropriate filter to installed in the entrance of the pump. The phenomenon
of high viscosity pump holding shaft mainly reflects in the stainless steel
of high viscosity pump is more, because of low carbon stainless steel material,
so the thermal expansion coefficient is big, once the temperature of the pump
is too high, can cause the interior of the pump parts and accessories the clearance
between the narrow, to a certain degree after tends to lock phenomenon. So
choose stainless steel high viscosity pump is must indicate the specific temperature,
and medium lubricity. The discretion of the medium viscosity and high viscosity
pump rotating speed of the intimate relationship. If the high viscosity pump
medium viscosity is too high, and with the rotation speed is too high, will
cause the pump flow rate is very low, the noise of the pump is very large.
If motor power or conventional match, then the motor can cause overload. Mainly
is the pump speed is too high, medium and high viscosity resistance is very
big, this will cause pump motor moment of starting current more than rated
current, motor overload; Due to high speed, high viscosity pump inside the
rotor is barely formed when running idle, surrounding medium by sliding, cause
not feeding, or flow rate is small. Under this situation, we must reduce the
speed of pump, increase the power of the motor, increase the import and export
of pipe diameter to reduce the flow resistance of the medium. Thus to complete
medium transport work. Speed is reduced, the pump flow rate will increase instead,
and the noise of the pump will be lower, but certainly can't flow theory. So
if you need to flow with the actual working condition differ too much, it can
only be better model bigger pump.
高粘度泵容易出現的另一個問題就是從動齒輪的銷軸容易磨損，特別是對于輸送沒有潤滑性的介質時，銷軸磨損特別快。對此我公司改進加工工藝在原有的基礎之上通過特殊設計改進給銷軸配套加了一套注油潤滑系統。在高粘度泵正常運轉的情況下通過內轉子的旋轉產生的離心力形成的負壓，利用注油系統通過特殊通道給銷軸注油，從而解決了高粘度泵銷軸磨損快的這一泵行業中存在的難題。Another
problem of the high viscosity pump is driven gear pin easy to wear and tear,
especially for conveying without lubrication medium, pin shaft wear particularly
fast. I improved processing technology on the basis of the original company
through special design improvements to pin shaft supporting a grease lubrication
system. Under the condition of the high viscosity of the normal operation of
pump centrifugal force produced by the rotation of the rotor within the formation
of the negative pressure, the use of injection system through the special channel
to pin shaft oil, so as to solve the high viscosity pump pin shaft quick wear
of the problems that exist in the pump industry.
|
